Some Good people at Eurofab Technologies Ltd. are to bend it on a press brake.
www.eurofab.ie
There was a smaller test piece also marked up for the setup
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEjp6iJev_0MijSRRuBkT61E4mEMBGjPrq628-n3e7TNf9hpyf8HpNeH4J_Ekh-pgpvn1azPK3PeijzFbaxTLgKMn2IUS7IcN3kfLym8FKosRQ_Msv_7S0Q_shwBVSEzDpg4oY6KLzLS0euj/s320/25-10-08+02.jpg)
12th Feb we get a clear hour to do the bend as the factory is usually busy doing lots of repeat work.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEiOkMCC7ZI6AoRlW9ij4yk3wwJOwXYCjWeusdGRMPp3OmyBDfrQOuTEbugGm3ZpYboz09QPSzDUScdJHjC57R0SqXxVqkGRA9NGv2jIYgJh2PGWaquTp9G88w_rTARC5sw5jS1bNAYYRgbU/s320/12-02-09+011.jpg)
First test piece 90 % correct.
We also did a piece only 2mm thick to get the bend radius correct.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEiqhNG7rVbbSqMFvDIseTZd1DN70E10hoxlAHiom415hPv_uCwCpItU7Wnjx4ouO_SfuX_On2EirztOOw1dotOx66r_SVXBcywNgkDu6m8wXsHn3op2-w0s0h2hKgzo8HhyphenhyphenNJOvCivVlSdm/s320/12-02-09+013.jpg)
Final piece ready to get bent. I had the sheet marked at 22 degree intervals, we decided that more hits at 11 degrees would give a better shape.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEihIIDzM3sJW0xbmj6OWGb1epmORmIlurzMYfMZ8YEFQmMg7A3-JnBZ_QgTlT1pPaKjv6JA3a8EIBIZG3UrlAXjk8AqRRyVgjzp6Q73Hl-L7FcIgQkH1DsxGL_UHLvJuFvgoscUMqF-sAOG/s320/12-02-09+016.jpg)
All setup to go. 1 piece and 1 go. !!!
The Boys werent worried.....
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEjLACXEWddUdh5-Issat0z7WVEAS7LVb2h8ApsEd6tagmJYE_EqeFWLnmhdVkM9F5U4DL9WM3019OQx75kdWgvLObMgGP68MVOf7QLdypnotvNteLRqptUBg_NJtZ9pVVn8Ekpshw5ooMR3/s320/12-02-09+017.jpg)
Naturally the piece is 100% perfect. 270 mm Dia at the top and 110mm at the bottom.
Better than I expected.
0 komentar:
Posting Komentar